View G104X1-L01_4899494.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Appr oval
TFT LCD Approval Specification
MODEL NO.: G104X1 - L01
Customer: Approved by: Note:
FOR MORE INFORMATION: AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA 92656 Http://www.AZDISPLAYS.com
Oy 2008-10-06 10:53:31 CST
u@ PMMD Director
1/4f(R)O cs_lee(oOt /17564/44926)
|a
e1/4
Director Accept
1
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
- CONTENTS REVISION HISTORY 1. GENERAL DESCRIPTION
1.1 OVERVIEW 1.2 FEATURES 1.3 APPLICATION 1.4 GENERAL SPECIFICATIONS 1.5 MECHANICAL SPECIFICATIONS -------------------------------------------------------------------------------------------------------------
3 4
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT 2.2 ELECTRICAL ABSOLUTE RATINGS 2.2.1 TFT LCD MODULE
-------------------------------------------------------
5
3. ELECTRICAL CHARACTERISTICS
------------------------------------------------------3.1 TFT LCD MODULE 3.2 BACKLIGHT UNIT 3.2.1 CCFL (Cold Cathode Fluorescent Lamp) CHARACTERISTICS
6
4. BLOCK DIAGRAM
4.1 TFT LCD MODULE 4.2 BACKLIGHT UNIT
-------------------------------------------------------
8
5. INTERFACE PIN ASSIGNMENT
5.1 TFT LCD MODULE 5.2 BLOCK DIAGRAM OF INTERFACE 5.3 BACKLIGHT UNIT 5.4 LVDS INTERFACE 5.5 COLOR DATA INPUT ASSIGNMENT
-------------------------------------------------------
9
6. INTERFACE TIMING
6.1 INPUT SIGNAL TIMING SPECIFICATIONS 6.2 POWER ON/OFF SEQUENCE
-------------------------------------------------------
14
7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS 7.2 OPTICAL SPECIFICATIONS
-------------------------------------------------------
17
8. DEFINITION OF LABELS
8.1 CMO MODULE LABEL
-------------------------------------------------------
21 22
9. PACKAGING
9.1 PACKING SPECIFICATIONS 9.2 PACKING METHOD
-------------------------------------------------------
10. PRECAUTIONS
10.1 ASSEMBLY AND HANDLING PRECAUTIONS 10.2 SAFETY PRECAUTIONS
-------------------------------------------------------
24
11. MECHANICAL CHARACTERISTIC
-------------------------------------------------------
25
2
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
REVISION HISTORY
Version Ver 2.0 Date Apr. 17, `07 Page (New) All 5 Section All 2.1 Description Approval Specification was first issued. Modify ABSOLUTE RATINGS OF ENVIRONMENT Storage TemperatureG (-20) ~ (+65) (- 20) ~ (+80) Operating Ambient temperatureG (-10) ~ (+60) (-20) ~ (+70) Correct TFT LCD Module Figure. (Remove frame buffer) Modify OPTICAL SPECIFICATIONSG Color Chromaticity (the same as G104X1-P01) Rx 0.631 0.629 Ry 0.349 0.348 Gx 0.306 0.306 Gy 0.569 0.560 Bx 0.150 0.150 By 0.113 0.102 Wx 0.336 0.329 Wy 0.357 0.346 MECHANICAL CHARACRTERISTIC Remove CMO Logo on metal frame from the drawing. Add aluminum foil on metal frame. Modify FeaturesG Fast response time Ton+Toff average 40 ms Ton+Toff average 25 ms Modify Response Time TRG 30 14 ms Typ. 35 TFG 10 11 ms Typ. 15
8 17
4.1 7.2
25
11
Ver 2.1
Oct. 9, `07
4
1.2
17
7.2
19 ms Max. 16 ms Max.
19
7.2
Note(6) Update Measurement Setup Diagram
Ver 2.2
Aug. 26, `08
24
10.1
Add precaution of "Image sticking" in section 10.1 Assembly and handling precautions (11) Do not keep same pattern in a long period of time. It may cause image sticking on LCD
3
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
1. GENERAL DESCRIPTION
1.1 OVERVIEW
G104X1- L01 is a 10.4" TFT Liquid Crystal Display module with 2-CCFL backlight unit and 30-pin-and-1ch LVDS interface. This product supports 1024 x 768 XGA format and can display true 16.2M colors (6-bits colors with FRC). The inverter module for backlight is not built-in.
1.2 FEATURES
- Excellent brightness (400 nits) - Ultra high contrast ratio (1200:1) - Fast response time (Ton+Toff average 25 ms) - High color saturation NTSC 57% - XGA (1024 x 768 pixels) resolution - DE (Data Enable) only mode - LVDS (Low Voltage Differential Signaling) interface - Ultra wide viewing angle: 176(H)/ 176(V) (CR>10) Super MVA technology -180 degree rotation display option -Color reproduction (Nature color) -Wide operation and storage temperature range (-20J to 70J operation, -20J to 80J storage)
1.3 APPLICATION
-TFT LCD for Avionics and Industrial applications - High brightness, multi-applications display
1.4 GENERAL SPECIFICATI0NS
Item Active Area Bezel Opening Area Driver Element Pixel Number Pixel Pitch (Sub Pixel) Pixel Arrangement Display Colors Display Operation Mode Surface Treatment Specification 210.4 (H) x 157.8 (V) (10.4" diagonal) 215.4 (H) x 161.8 (V) a-si TFT active matrix 1024 x R.G.B. x 768 0.0685 (H) x 0.2055 (V) RGB vertical stripe 16.2 M Transmissive mode / Normally black Anti-Glare coating (Haze 25%) Hard coating (3H) Unit mm mm pixel mm color Note (1) -
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.
4
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
1.5 MECHANICAL SPECIFICATIONS
Item Horizontal (H) Module Size Vertical (V) Depth (D) Weight Min. 225 175.8 9.67 Typ. 225.5 176.3 10.17 480 Max. 226 176.8 10.67 Unit mm mm mm g Note (1) -
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Test Item High Temperature Storage Test Low Temperature Storage Test Thermal Shock Storage Test High Temperature Operation Test Low Temperature Operation Test High Temperature & High Humidity Operation Test Shock (Non-Operating) Vibration (Non-Operating) Test Condition 80C, 240 hours -20C, 240 hours -20C, 0.5hour/o 70J , 0.5hour; 100cycles, 1hour/cycle 70C, 240 hours -20C, 240 hours 60C, 90%RH, 240hours 200G, 2ms, half sine wave, 1 time for X, Y, Z. 1.5G, 10 ~ 300 Hz, 10min/cycle, 3 cycles each X, Y, Z (3) (3) Note
(1) (2)
Note (1) There should be no condensation on the surface of panel during test. Note (2) Temperature of panel display surface area should be 80 C Max. Note (3) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture.
2.2 ELECTRICAL ABSOLUTE RATINGS 2.2.1 TFT LCD MODULE
Item Power Supply Voltage Input Signal Voltage Symbol Vcc VIN Value Min. -0.3 -0.3 Max. 4.0 3.6 Unit V V Note (1)
Note (1) Permanent damage to the device may occur if maximum values are exceeded. Functional operation should be restricted to the conditions described under normal operating conditions.
5
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE
Parameter Power Supply Voltage Power Supply Ripple Voltage Rush Current White Power Supply Current Black Vertical Stripe Differential Input High Threshold Voltage LVDS Differential Input Low Interface Threshold Voltage Common Input Voltage Terminating Resistor CMOS Input High Threshold Voltage interface Input Low Threshold Voltage Note (2) Measurement Conditions: Symbol VCC VRP IRUSH ICC VLVTH VLVTL VLVC RT VIH VIL Min. 3.0 -100 1.125 2.7 0 Value Typ. 3.3 1.1 0.8 1.0 1.25 100 Max. 3.6 100 1.8 1.4 +100 1.375 3.3 0.7 Ta = 25 2 C Unit V mV A A A A mV mV V ohm V V Note (1) (2) (3) -
Note (1) The assembly should be always operated within above ranges.
6
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
Vcc rising time is 470us
+3.3V
0.9Vcc 0.1Vcc
GND 470s
Note (3) The specified power supply current is under the conditions at Vcc = 3.3 V, Ta = 25 2 C, fv = 60 Hz, whereas a power dissipation check pattern below is displayed. a. White Pattern b. Black Pattern
Active Area
Active Area
c. Vertical Stripe Pattern
RGBRGB BRGBRGBR BRGBRGBR RGBRGB
Active Area
7
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
3.2 BACKLIGHT UNIT 3.2.1 CCFL (Cold Cathode Fluorescent Lamp) CHARACTERISTICS (Ta = 25 2 C)
Parameter Lamp Voltage Lamp Current Lamp Starting Voltage Operating Frequency Lamp Life Time and slave board. Note (2) The lamp starting voltage VS should be applied to the lamp for more than 1 second after startup. Otherwise the lamp may not be turned on. Note (3) The lamp frequency may produce interference with horizontal synchronous frequency of the display input signals, and it may result in line flow on the display. In order to avoid interference, the lamp frequency should be detached from the horizontal synchronous frequency and its harmonics as far as possible. Note (4) The lifetime of lamp can be defined as the time in which it continues to operate under the condition Ta = 25 O 2 oC and IL = 7 mArms until one of the following events occurs: (a) When the brightness becomes or lower than 50% of its original value. (b) When the effective ignition length becomes O 80% of its original value. (The effective ignition Symbol VW IL VS FO LBL Min. 6.5 45 50,000 Value Typ. 460 7 Max. 7.5 770 960 80 Unit VRMS mARMS VRMS VRMS KHz Hrs Note IL = 7.0mA (1) (2) at 25J (2),at 0J (3) (4)
Note (1) Lamp current is measured by utilizing AC current probe and its value is average by measuring master
length is a scope that luminance is over 70% of that at the center point.)
4. BLOCK DIAGRAM
4.1 TFT LCD MODULE
SCAN DRIVER IC
RX0(+/-) RX1(+/-) RX2(+/-) RX3(+/-) RXCLK(+/-)
TFT LCD PANEL (1024x3x768)
(JAE,FI-XB30SRL-HF11)
INPUT CONNECTOR
TIMING CONTROLLER
Vcc GND
DATA DRIVER IC DC/DC CONVERTER & REFERENCE VOLTAGE
8
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
4.2 BACKLIGHT UNIT
5. INTERFACE PIN CONNECTION
5.1 TFT LCD MODULE
CN1 Connector Pin Assignment Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Symbol NC GND RX3+ RX3GND RXCLK+ RXCLKGND RX2+ RX2GND RX1+ RX1GND RX0+ RX0GND STV GND NC NC NC NC RPF GND GND GND VCC VCC VCC Description No Connection Ground Positive transmission data of pixel 3 Negative transmission data of pixel 3 Ground Positive of clock Negative of clock Ground Positive transmission data of pixel 2 Negative transmission data of pixel 2 Ground Positive transmission data of pixel 1 Negative transmission data of pixel 1 Ground Positive transmission data of pixel 0 Negative transmission data of pixel 0 Ground Vertical Start Pulse Output Ground No Connection No Connection No Connection No Connection Reverse Panel Function (Display Rotation) Ground Ground Ground Power supply: +3.3V Power supply: +3.3V Power supply: +3.3V Note (2) (3) -
Note (1) Connector Part No.: JAE,FI-XB30SRL-HF11 or compatible Note (2) Reserved for internal use. Please leave it floating.
9
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
Note (3) Scanning direction:
RPF = Low/ floating : normal display (default)
RPF = High : display with 180 degree rotation
5.2 BLOCK DIAGRAM OF INTERFACE CN1
Rx0+ R0-R7 G0-G7 B0-B7 DE TxIN Rx0-
51[
100pF
RxOUT
51[
R0-R7 G0-G7
100pF
Rx1+ Rx1-
51[
51[
B0-B7 DE
Rx2+ Rx2Rx3+ Rx3-
51[
100pF
51[ 51[
100pF
51[
Host Graphics Controller LVDS Transmitter THC63LVDM83A (LVDF83A) PLL
CLK+ CLK-
51[
100pF
PLL
DCLK Timing Controller
51[
LVDS Receiver THC63LVDF84A
R0~R7 G0~G7 B0~B7 DE
: Pixel R Data , : Pixel G Data , : Pixel B Data ,
: Data enable signal
10
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
Note (1) The system must have the transmitter to drive the assembly. Note (2) LVDS cable impedance shall be 50 ohms per signal line or about 100 ohms per twist-pair line when it is used differentially.
5.3 BACKLIGHT UNIT Pin Symbol Description 1 LV Ground 2 HV1 High Voltage 3 HV2 High Voltage Note (1): Connector Part No: BHR-03VS-1 (JST Mfg. Co., Ltd)
Remark White Pink Pink
11
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
5.4 LVDS INTERFACE
TRANSMITTER SIGNAL THC63LVDM83A PIN R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 24 bit B2 B3 B4 B5 DE R6 R7 G6 G7 B6 B7 RSVD 1 RSVD 2 RSVD 3 DCLK 51 52 54 55 56 3 4 6 7 11 12 14 15 19 20 22 23 24 30 50 2 8 10 16 18 25 27 28 31 INPUT TxIN0 TxIN1 TxIN2 TxIN3 TxIN4 TxIN6 TxIN7 TxIN8 TxIN9 TxIN12 TxIN13 TxIN14 TxIN15 TxIN18 TxIN19 TxIN20 TxIN21 TxIN22 TxIN26 TxIN27 TxIN5 TxIN10 TxIN11 TxIN16 TxIN17 TxIN23 TxIN24 TxIN25 TxCLK IN TxCLK OUT+ RxCLK IN+ TxCLK OUT- RxCLK INR0~R7: Pixel R Data (7; MSB, 0; LSB) G0~G7: Pixel G Data (7; MSB, 0; LSB) B0~B7: Pixel B Data (7; MSB, 0; LSB) DE: Data enable signal Notes (1) RSVD(reserved)pins on the transmitter shall be "H" or "L". TA OUT3Rx 3TA OUT3+ Rx 3+ TA OUT2Rx 2TA OUT2+ Rx 2+ TA OUT1Rx 1TA OUT1+ Rx 1+ TA OUT0Rx 0TA OUT0+ Rx 0+ INTERFACE CONNECTOR Host TFT-LCD RECEIVER THC63LVDF84A PIN 27 29 30 32 33 35 37 38 39 43 45 46 47 51 53 54 55 1 6 7 34 41 42 49 50 2 3 5 26 OUTPUT Rx OUT0 Rx OUT1 Rx OUT2 Rx OUT3 Rx OUT4 Rx OUT6 Rx OUT7 Rx OUT8 Rx OUT9 Rx OUT12 Rx OUT13 Rx OUT14 Rx OUT15 Rx OUT18 Rx OUT19 Rx OUT20 Rx OUT21 Rx OUT22 Rx OUT26 Rx OUT27 Rx OUT5 Rx OUT10 Rx OUT11 Rx OUT16 Rx OUT17 Rx OUT23 Rx OUT24 Rx OUT25 RxCLK OUT TFT CONTROL INPUT R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 DE R6 R7 G6 G7 B6 B7 NC NC NC DCLK
12
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
5.5 COLOR DATA INPUT ASSIGNMENT
The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input. Data Signal Color Black Red Green Basic Blue Colors Cyan Magenta Yellow White Red(0) / Dark Red(1) Gray Scale Of Red Red(2) : : Red(253) Red(254) Red(255) Green(1) Gray Scale Of Green Green(2) : : Green(253) Green(254) Green(255) Blue(0) / Dark Blue(1) Gray Scale Of Blue Blue(2) : : Blue(253) Blue(254) Blue(255) 0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 Red 0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 1 0 0 0 1 1 1 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 1 0 0 0 1 1 1 0 0 1 : : 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 Green 00000 10000 01111 00000 01111 10000 11111 11111 00000 10000 00000 : : : : : : : : : : 0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 : : 0 0 0 0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 0 1 : : 0 1 1 0 0 0 : : 0 0 0 0 0 1 0 1 0 1 1 0 0 0 : : 0 0 0 0 1 0 : : 1 0 1 0 0 0 : : 0 0 0 00 00 00 11 11 11 00 11 00 00 00 : : : : 0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 Blue 0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 0 : : 0 0 0 0 0 0 : : 1 1 1 000 000 000 111 111 111 000 111 000 000 000 : : : : : :
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
10000 00000 10000 00000 00000 00000 : : : : : : : : : :
00 00 00 00 00 00 : : : :
000 000 000 000 000 000 : : : : : :
Green(0) / Dark 0
01111 01111 01111 00000 00000 00000 : : : : : : : : : :
00 00 00 00 00 00 : : : :
000 000 000 000 001 010 : : : : : :
00000 00000 00000
11 11 11
101 110 111
Note (1) 0: Low Level Voltage, 1: High Level Voltage
6. INTERFACE TIMING
13
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
The input signal timing specifications are shown as the following table and timing diagram. Signal LVDS Receiver Clock Item Frequency Input cycle to cycle jitter LVDS Receiver Data Setup Time Hold Time Frame Rate Total Display Blank Total Horizontal Active Display Term Display Blank Symbol 1/Tc Trcl Tlvsu Tlvhd Fv Tv Tvd Tvb Th Thd Thb Min. 55 600 600 50 770 768 2 1100 1024 76 Typ. 65 60 806 768 38 1344 1024 320 Max. 75 200 70 950 768 182 1800 1024 776 Unit MHZ ps ps ps Hz Th Th Th Tc Tc Tc Tv=Tvd+Tvb Th=Thd+Thb Note
Vertical Active Display Term
Note (1) Since this assembly is operated in DE only mode, Hsync and Vsync input signals should be set to low logic level. Otherwise, this assembly would operate abnormally.
INPUT SIGNAL TIMING DIAGRAM
Tv Tvd Tvb
DE Th
DCLK Tc DE Thb Thd
DATA
Valid display data (1024 clocks)
14
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
LVDS RECEIVER INTERFACE TIMING DIAGRAM
Tc
RXCLK+/-
RXn+/Tlvsu Tlvhd
1T 14
3T 14
5T 14
7T 14
9T 14
11 T 14
13T 14
15
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
6.2 POWER ON/OFF SEQUENCE
To prevent a latch-up or DC operation of LCD assembly, the power on/off sequence should be as the diagram below.
Power Supply VCC
0V 0.5O 0O 0O T1O T2O T3O 10ms 50ms 50ms T4
0.9 VCC 0.1VCC
0.9 VCC 0.1Vcc
T1
T3
500ms O
T2
T4
Signals
0V
VALID
Power On
Power Off
Backlight (Recommended) 500msO T5 100msO T6
T5
50%
50%
T6
Power ON/OFF Sequence
Note (1) The supply voltage of the external system for the assembly input should follow the definition of Vcc. Note (2) Apply the lamp voltage within the LCD operation range. When the backlight turns on before the LCD operation or the LCD turns off before the backlight turns off, the display may momentarily become abnormal screen. Note (3) In case of Vcc is in off level, please keep the level of input signals on the low or keep a high impedance. Note (4) T4 should be measured after the assembly has been fully discharged between power off and on period. Note (5) Interface signal shall not be kept at high impedance when the power is on.
16
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS
Item Ambient Temperature Ambient Humidity Supply Voltage Input Signal Lamp Current Oscillating Frequency (Inverter) Vertical Frame Rate Inverter Symbol Value Unit o Ta C 252 Ha %RH 5010 VCC 5.0 V According to typical value in "3. ELECTRICAL CHARACTERISTICS" IL 7 mA FW 61 KHz Fr 60 Hz Sumida IV40090T/B2
7.2 OPTICAL SPECIFICATIONS
The relative measurement methods of optical characteristics are shown in 7.2. The following items should be measured under the test conditions described in 7.1 and stable environment shown in Note (6). Item Contrast Ratio Response Time Center Luminance of White White Variation Cross Talk Red Green Color Chromaticity Blue White Color Gamut Viewing Angle Horizontal Vertical Symbol CR TR TF LC W CT Rx Ry Gx Gy Bx By Wx Wy CG x+ xY+ YCondition Min. 900 350 Typ. 1200 14 11 400 0.629 0.348 0.306 0.560 0.150 0.102 0.329 0.346 57 88 88 88 88 Max. 19 16 1.4 4 Unit ms ms Note (2) (3) (4) (7) (5)
x=0, Y =0 Viewing angle at normal direction
Typ. -0.03
cd/m2 % Typ. +0.03 -
(6)
CR10
55 80 80 80 80
-
% Deg.
NTSC (1)
17
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
Note (1) Definition of Viewing Angle (x, y): Viewing angles are measured by BM5A Normal x = y = 0 yX- = 90 xx- x+ y+ 12 o'clock direction y+ y+ = 90
6 o'clock y- = 90
y-
x+
X+ = 90
Note (2) Definition of Contrast Ratio (CR): The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L255 / L0 L255: Luminance of gray level 255 L 0: Luminance of gray level 0 CR = CR (5), where CR (X) is corresponding to the Contrast Ratio of the point X at the figure in Note (7). Note (3) Definition of Response Time (TR, TF):
Gray Level 255
100% 90%
Gray Level 255
Optical Response Gray Level 0
10% 0%
Time TF TR
.
18
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
Note (4) Definition of Luminance of White (LC): Measure the luminance of gray level 255 at center point and 5 points LC = L (5), where L (X) is corresponding to the luminance of the point X at the figure in Note (7). Note (5) Definition of Cross Talk (CT): CT = | YB - YA | / YA x 100 (%) Where: YA = Luminance of measured location without gray level 0 pattern (cd/m2) YB = Luminance of measured location with gray level 0 pattern (cd/m2) Active Area
YA, U (D/2,W/8) (D/4,W/4) YA, L (D/8,W/2)
(0, 0)
(0, 0)
Active Area
YB, U (D/2,W/8)
Gray 128
YB, L (D/8,W/2) YA, R (7D/8,W/2) YB, D (D/2,7W/8) (D,W)
Gray 0 0 Gray
Gray 128
YB, R (7D/8,W/2) (3D/4,3W/4)
YA, D (D/2,7W/8)
(D,W)
Note (6) Measurement Setup: The LCD assembly should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 30 minutes in a windless room.
LCD Module LCD Panel USB2000 CS-1000T
Field of View = 2 Center of the Screen 500 mm
Light Shield Room (Ambient Luminance < 2 lux)
19
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
Note (7) Definition of White Variation (W): Measure the luminance of gray level 255 at 5 points W = Maximum [L (1), L (2), L (3), L (4), L (5)] / Minimum [L (1), L (2), L (3), L (4), L (5)]
Horizontal Line D
D/4 D/2 3D/4
Vertical Line
W/4
1
2
W
W/2
5
X
: Test Point X=1 to 5
3W/4
3
4
Active Area
20
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
8.DEFINITION OF LABELS
8.1 CMO MODULE LABEL
The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation.
CHI
MEI
E207943
G104X1 -L01 Rev.XX
MADE IN TAIWAN
OPTOELECTRONICS
RoHS XXXXXXXYMDLNNNN
(a) Model Name: G104X1-L01 (b) Revision: Rev. XX, for example: A0, A1... B1, B2... or C1, C2...etc. (c) Serial ID: X X X X X X X Y M D L N N N N Serial No. Product Line Year, Month, Date CMO Internal Use CMO Internal Use Revision CMO Internal Use Serial ID includes the information as below: (a) Manufactured Date: Year: 0~9, for 2000~2009 Month: 1~9, A~C, for Jan. ~ Dec. Day: 1~9, A~Y, for 1st to 31st, exclude I ,O, and U. (b) Revision Code: Cover all the change (c) Serial No.: Manufacturing sequence of product (d) Product Line: 1 -> Line1, 2 -> Line 2, ...etc.
21
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
9. PACKAGING
9.1 PACKING SPECIFICATIONS
(1) 30 LCD modules / 1 Box (2) Box dimensions : 500(L) X 400 (W) X 330 (H) (3) Weight : approximately 15.5Kg (30 LCD modules per box)
9.2 PACKING METHOD
Figures 9-1 and 9-2 are the packing method
Figure.9-1 packing method
22
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
Figure. 9-2 Packing method
23
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
10. PRECAUTIONS
10.1 ASSEMBLY AND HANDLING PRECAUTIONS
(1) Do not apply rough force such as bending or twisting to the module during assembly. (2) It is recommended to assemble or to install a module into the user's system in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. (3) Do not apply pressure or impulse to the module to prevent the damage of LCD panel and Backlight. (4) Always follow the correct power-on sequence when the LCD module is turned on. This can prevent the damage and latch-up of the CMOS LSI chips. (5) Do not plug in or pull out the I/F connector while the module is in operation. (6) Do not disassemble the module. (7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched. (8) Moisture can easily penetrate into LCD module and may cause the damage during operation. (9) High temperature or humidity may deteriorate the performance of LCD module. Please store LCD modules in the specified storage conditions. (10) When ambient temperature is lower than 10C, the display quality might be reduced. For example, the response time will become slow, and the starting voltage of CCFL will be higher than that of room temperature. (11) Do not keep same pattern in a long period of time. It may cause image sticking on LCD.
10.2 SAFETY PRECAUTIONS
(1) The startup voltage of a Backlight is approximately 1000 Volts. It may cause an electrical shock while assembling with the inverter. Do not disassemble the module or insert anything into the Backlight unit. (2) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. (3) After the module's end of life, it is not harmful in case of normal operation and storage.
24
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
11. MECHANICAL CHARACTERISTICS
25
CHI MEI
(c)q l N- / |1/2 q _u
Version2.2
Issued Date: Aug. 26, 2008 Model No.: G104X1-L01
Approval
26
CHI MEI
ql1/2q u _ (c) - / N|
Version2.2

▲Up To Search▲

Price & Availability of G104X1-L01

	To Download G104X1-L01 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .